Nissan Juke Service and Repair Manual : Precaution for Brake Control system
• Always perform a pre-driving check to drive the vehicle.• Always perform a pre-driving check to drive the vehicle.
• Always check speed and safety while driving the vehicle.
• Always check speed and safety while driving the vehicle.
• To operate CONSULT-III while driving, more than one person is required to be in the vehicle to avoid interference to driving and ensure safety.
• Slight vibrations are felt on the brake pedal and the operation noises occur, when ABS function or EBD function operates. This is not a malfunction because it is caused by ABS function or EBD function that is normally operated.
• When starting engine or when starting vehicle just after starting engine, brake pedal may vibrate or motor operating noise may be heard from engine compartment. This is normal condition.
• Brake stopping distance may become longer than models without ABS function depending on the road conditions, when ABS function is operated on slippery road like rough road, gravel road or snowy road.
• When a malfunction is indicated, always collect information from the customer about conditions of occurrence, estimate cause and perform operation. Check brake booster operation, brake fluid level and brake fluid leakage, as well as electrical system.
• The optimum performance is achieved by control for ABS function or EBD function when all of brakes, suspensions and tires installed on the vehicle are the specified size and parts. Brake performance and controllability may be negatively affected when other parts than the specified are installed.
• Brake stopping distance may become longer and steering stability may be negatively affected, when tires in different size and combination or other parts than the specified are used.
• When a radio (including wiring), antenna and antenna lead line are located near ABS actuator and electric unit (control unit), a malfunction or improper operation may occur for the control of ABS function or EBD function.
• When the following items are replaced by other parts than genuine parts or modified, ABS warning lamp and brake warning lamp may turn ON, and the control may not operate normally for ABS function or EBD function.
- Suspension component parts (shock absorber, spring, bushing and others) - Tire and wheel (other than the specified size) - Brake component parts (brake pad, disc rotor, brake caliper and others) - Engine component parts (ECM, muffler and others) - Body reinforcement component parts (rollover bar, tower bar and others)
• When suspension, tire and brake component parts are excessively worn or deteriorated and the vehicle is driven, ABS warning lamp and brake warning lamp may turn ON, and the control may not operate normally for ABS function or EBD function.
• ABS warning lamp and brake warning lamp may turn ON, when only front wheel or rear wheel is rotated using a free roller. This is not a malfunction, because it is caused by wheel speed difference between wheel that is rotated and wheel that is not rotated. In this case, perform self-diagnosis, check self-diagnosis results, and erase memory.
• When power supply voltage is not normal, ABS warning lamp and brake warning lamp turn ON. ABS actuator and electric unit (control unit) stops control for ABS function or EBD function. Ordinary brake operates.
After power supply returns to normal, ABS warning lamp and brake warning lamp turn OFF. The control becomes operative for ABS function or EBD function.
Precaution for Brake System
WARNING:
Clean any dust from the front brake and rear brake using a vacuum dust
collector. Never blow by compressed
air.
• Brake fluid use refer to MA-13, "Fluids and Lubricants".
• Ne ...
Other materials:
Windshield wiper and washer switch
WARNING
In freezing temperatures the washer solution may freeze on the windshield
and obscure your vision which may lead to an accident. Warm windshield with the
defroster before you wash the windshield.
CAUTION
• Do not operate the washer continuously for more than 30 seconds.
• Do not oper ...
B1120 satellite sensor LH
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp statu ...
Additional service when replacing transaxle assembly
Description
Perform the following work after the transaxle assembly is replaced.
Erasing the calibration data
• The TCM acquires calibration data (individual characteristic value) of each
solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accu ...