Nissan Juke Owners Manual : Maintenance precautions
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed.
WARNING
• Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift lever to the P (Park) position (CVT model) or the shift lever to the N (Neutral) position (MT model).
• Be sure the ignition switch is in the OFF or LOCK position when performing any parts replacement or repairs.
• If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.
• It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc.
before working on your vehicle.
• Always wear eye protection whenever you work on your vehicle.
• If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.
• Never get under the vehicle while it is supported only by a jack. If it is necessary to work under the vehicle, support it with safety stands.
• Keep smoking materials, flame and sparks away from fuel tank and the battery.
• The fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.
CAUTION
• Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.
• Avoid direct contact with used engine oil and coolant. Improperly disposed engine oil, and engine coolant and/or other vehicle fluids can damage the environment. Always conform to local regulations for disposal of vehicle fluid.
• Never leave the engine or the CVT related component harnesses disconnected while the ignition switch is in the ON position.
• Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position.
• Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan.
This “8. Maintenance and do-it-yourself” section gives instructions regarding only those items which are relatively easy for an owner to perform.
A genuine NISSAN Service Manual is also available. (See “Owner’s manual/service manual order information” .) You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect your warranty coverage. If in doubt about any servicing, we recommend that it be done by a NISSAN dealer.
General maintenance
During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smell, be su ...Engine compartment check locations
MR16DDT ENGINE 1. Engine oil filler cap 2. Radiator filler cap 3. Brake and clutch fluid reservoir 4. Air cleaner 5. Window washer fluid reservoir 6. Engine drive belt location 7. Engine oil ...Other materials:
Liquid Gasket
REMOVAL OF LIQUID GASKET
• After removing mounting nuts and bolts, separate the mating surface
using the seal cutter [SST: KV10111100] (A) and remove old
liquid gasket sealing.
CAUTION:
Be careful not to damage the mating surfaces.
• Tap the seal cutter [SST: KV10111100] to insert it (B), an ...
Service data and specifications (SDS)
General Specifications
MR16DDT
HR16DE, K9K
Brake Pedal
Brake Booster
2WD
4WD
Front Disc Brake
MR16DDT
HR16DE, K9K
Rear Disc Brake
...
Key out interlock door unlock function does not operate
Diagnosis Procedure
1.CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT-III.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
Refer to DLK-501, "DOOR LOCK ...