Nissan Juke Service and Repair Manual : Radiator core support

HR16DE

HR16DE : Exploded View

1. Radiator core support upper


1. Radiator core support upper 2. Air guide RH (MT models) 3. Radiator core support lower 4. Air guide LH 5. Air guide (upper) 6. Air guide LH (CVT models) 7. Air guide RH (CVT models)

HR16DE : Removal and Installation: N·m (kg-m, ft-lb)


HR16DE : Removal and Installation

RADIATOR CORE SUPPORT UPPER

Removal
1. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation".

2. Remove front combination lamp (LH and RH). Refer to EXL-91, "Removal and Installation".

3. Remove headlamp (LH and RH). Refer to EXL-89, "Removal and Installation".

4. Disconnect crash zone sensor harness connector. Refer to SR-26, "Removal and Installation".

CAUTION:
Turn ignition switch OFF, disconnect battery negative terminal and then wait for at least 3 minutes.

5. Remove hood lock and hood lock cable fixing clip. Refer to DLK-172, "HOOD LOCK : Removal and Installation".

6. Remove horn bracket. Refer to HRN-4, "Removal and Installation".

7. Remove air guide (upper) fixing clips, and then remove air guide (upper).

8. Remove upper fixing clips (2) of air guide (LH and RH) (1).

9. Remove hood support rod. Refer to DLK-146, "HOOD SUPPORT ROD : Removal and


9. Remove hood support rod. Refer to DLK-146, "HOOD SUPPORT ROD : Removal and Installation".

10. Remove mounting bolts, and then remove radiator core support upper.

Installation Install in the reverse order of removal.

RADIATOR CORE SUPPORT LOWER

Removal
1. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation".

2. Remove lower fixing clips (2) of radiator side seal (LH and RH) (1).

3. Use belts (A) to suspend radiator and condenser to prevent


3. Use belts (A) to suspend radiator and condenser to prevent them from falling.

CAUTION:
Never damage radiator and condenser.

4. Remove mounting bolts, and then remove radiator core support lower.


4. Remove mounting bolts, and then remove radiator core support lower.

Installation
Install in the reverse order of removal.

MR16DDT

MR16DDT : Exploded View

1. Radiator core support upper


1. Radiator core support upper 2. Air guide RH
3. Radiator core support lower 4. Air guide LH

A : 2WD models
B : 4WD models

MR16DDT : Removal and Installation: N·m (kg-m, ft-lb)


MR16DDT : Removal and Installation

RADIATOR CORE SUPPORT UPPER

Removal
1. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation".

2. Remove front combination lamp (LH and RH). Refer to EXL-91, "Removal and Installation".

3. Remove headlamp (LH and RH). Refer to EXL-89, "Removal and Installation".

4. Disconnect crash zone sensor harness connector. Refer to SR-26, "Removal and Installation".

CAUTION:
Turn ignition switch OFF, disconnect battery negative terminal and then wait for at least 3 minutes.

5. Remove hood lock and hood lock cable fixing clip. Refer to DLK-172, "HOOD LOCK : Removal and Installation".

6. Remove horn bracket. Refer to HRN-4, "Removal and Installation".

7. Remove upper fixing clips (2) of air guide (LH and RH) (1).

8. Remove hood support rod. Refer to DLK-146, "HOOD SUPPORT ROD : Removal and


8. Remove hood support rod. Refer to DLK-146, "HOOD SUPPORT ROD : Removal and Installation".

9. Remove mounting bolts, and then remove radiator core support upper.

Installation
Install in the reverse order of removal.

RADIATOR CORE SUPPORT LOWER

Removal
1. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation".

2. Remove lower fixing clips (2) of radiator side seal (LH and RH) (1).

3. Using strings (A), hang inlet hose (1) and inlet hose (2) together


3. Using strings (A), hang inlet hose (1) and inlet hose (2) together with charge air cooler.

CAUTION:
Never damage inlet hoses with charge air cooler.

4. Support lower side radiator using wooden blocks (B) and a floor


4. Support lower side radiator using wooden blocks (B) and a floor jack (A).

CAUTION:
Never damage radiator.

5. Remove mounting bolts, and then remove radiator core support lower.


5. Remove mounting bolts, and then remove radiator core support lower.

Installation
Install in the reverse order of removal.

    Hood
    Exploded View 1. Hood assembly 2. Hood bumper rubber 3. Radiator core seal 4. Hood bumper rubber 5. Clamp 6. Hood hinge 7. Grommet 8. Hood support rod : Clip : Pawl : Body grease Ho ...

    Front fender
    Exploded View 1. Front fender assembly 2. Front fender stiffener : Vehicle front Removal and Installation REMOVAL 1. Remove front fillet molding. Refer to EXT-26, "FRONT FILLET MOLDING : ...

    Other materials:

    Fuel tank
    2WD : Exploded View 1. Fuel filler cap 2. Grommet 3. Fuel filler tube 4. EVAP canister hose 5. Fuel tank mounting band (RH) 6. Fuel tank mounting band (LH) 7. Fuel tank 8. Clamp 9. Fuel filler hose 10. Vent hose Vehicle front : N?·m (kg-m, ft-lb) 2WD : Removal and Installation ...

    P181B incomplete selfshut
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.DTC REPRODUCTION PROCEDURE With ...

    Wheel alignment
    Inspection DESCRIPTION Measure wheel alignment under unladen conditions. NOTE: “Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. PRELIMINARY CHECK Check the following: • Tires for improper ai ...