Nissan Juke Owners Manual : Moonroof (if so equipped)
WARNING
• In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.
• Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
CAUTION
• Remove water drops, snow, ice or sand from the moonroof before opening.
• Do not place any heavy object on the moonroof or surrounding area.
AUTOMATIC MOONROOF
The moonroof only operates when the ignition switch is in the ON position.
The automatic moonroof is operational for about 45 seconds, even if the ignition switch is turned to the OFF position. If the driver’s door or the passenger’s door is opened during this period of about 45 seconds, power to the moonroof is canceled.
Sunshade
The sunshade will open automatically when the moonroof is opened. However, it must be closed manually.
Sliding the moonroof
To fully open or close the moonroof, push the switch toward
1 or
2 and release it; it need not be held.
The roof will automatically open or close all the way. To stop the roof, push the
switch in any direction while it is opening or closing.
Tilting the moonroof
To tilt up, first close the moonroof by pushing the switch toward
2 . Push the switch toward
2 again and release it; it need not
be held. To tilt down the moonroof, push the switch toward
1 .
Auto reverse function
WARNING
There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof.
If the control unit detects something caught in the moonroof when it is closing, the moonroof will be immediately opened.
The auto reverse function can be activated when the moonroof is closed by automatic operation when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is turned to the OFF position.
If the moonroof cannot be closed automatically when the auto reverse function
activates due to a malfunction, push and hold the switch toward
2 .
Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.
If the moonroof does not operate
If the moonroof does not operate properly, perform the following procedure to initialize the moonroof operation system.
1. If the moonroof is open, close it fully by repeatedly pushing the switch toward
2 .
2. Push and hold the switch toward 2
to tilt the moonroof up.
3. Release the moonroof switch after the moonroof moves slightly up and down.
4. Push and hold the switch toward 1
to fully tilt the moonroof down.
5. Check if the moonroof switch operates normally.
If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.
Windows
POWER WINDOWS
WARNING
• Make sure that all passengers have their hands, etc. inside the vehicle
while it is in motion and before closing the windows. Use the window lock switch
to prevent unexpe ...
Interior lights
CAUTION
Do not use for extended periods of time with the engine stopped. This could
result in a discharged battery. ...
Other materials:
ACC warning does not operate
Diagnosis Procedure
1.CHECK COMBINATION METER BUZZER
Check combination meter buzzer.
Refer to WCS-40, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.REPLACE BCM
1. Replace BCM. Ref ...
Diagnosis and repair work flow
Work Flow
OVERALL SEQUENCE
Reference 1··· Refer to AV-77, "Symptom Table".
DETAILED FLOW
1.CHECK SYMPTOM
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and
environment when the malfu ...
Diagnosis system (combination meter)
On Board Diagnosis Function
ON BOARD DIAGNOSIS ITEM
The combination meter allows the following diagnosis items with the on-board
diagnosis function.
METHOD OF STARTING
1. Turn ignition switch ON, and switch the trip meter to “trip A” or “trip
B”.
2. Turn ignition switch OFF.
3. While pre ...