Nissan Juke Service and Repair Manual : Front door lock
Exploded View
1. Door key cylinder assembly (driver
side)
Outside handle escutcheon (passenger
side)
2. Outside handle
3. Front gasket
4. Inside handle
5. TORX bolt
6. Door lock assembly
7. Key rod (driver side)
8. Outside handle bracket
9. Rear gasket
10. Key rod protector (driver side)
11. Cable clip
: Pawl
: Vehicle front
: Do not reuse
: N·m (kg-m, in-lb)
: Body grease
Door lock
DOOR LOCK : Removal and Installation
REMOVAL
1. Remove inside handle. Refer to DLK-176, "INSIDE HANDLE : Removal and Installation".
2. Disengage inside handle cable from cable clip.
3. Remove outside handle bracket. Refer to DLK-176, "OUTSIDE HANDLE : Removal and Installation".
4. Remove door lock assembly TORX bolts.
5. Disconnect door lock actuator connector, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Apply body grease to door lock if necessary.
: Grease up point
Inside handle
INSIDE HANDLE : Removal and Installat
REMOVAL
1. Remove front door finisher. Refer to INT-13, "Removal and Installation".
2. Remove inside handle mounting bolt (A).
3. Disengage inside handle (1) from door panel (2) while sliding inside handle toward vehicle rear, and then separate inside handle.
: Vehicle front
4. Disengage inside handle cable (2), and then remove inside handle (1).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
Outside handle
OUTSIDE HANDLE : Removal and Installation
REMOVAL
1. Remove front door glass and front door lower sash (rear). Refer to GW-17, "Removal and Installation".
2. Remove key rod protector mounting bolt and fixing clip, and then remove key rod protector.
3. Disengage lock holder (1), and then separate key rod (3) from door lock assembly (2).(Driver side)
4. Disconnect harness connector of door antenna (1) and door request switch (2) and remove harness clamp (3).
: Vehicle front
5. Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes door lock cylinder. (For passenger side, TORX bolt fixes outside handle escutcheon.)
6. While pulling outside handle (1), remove door key cylinder assembly (diver side) (2) or outside handle escutcheon (passenger side) (2).
7. While pulling outside handle (1), slide toward rear of vehicle to remove outside handle.
8. Remove front gasket (1) and rear gasket (2).
: Vehicle front
9. Slide outside handle bracket toward rear of vehicle to remove.
: Vehicle front
10. Disconnect outside handle cable (1) from outside handle bracket (2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
Hood lock
Exploded View 1. Hood lock control cable assembly 2. Hood lock assembly : Clip : N·m (kg-m, ft-lb) : Body grease Hood lock HOOD LOCK : Removal and Installation REMOVAL 1. Remove front cent ...Rear door lock
Exploded View 1. Outside handle assembly 2. Inside handle 3. TORX bolt 4. Door lock assembly 5. Rear door sealing screen : Clip : Pawl : Vehicle front : Do not reuse : N·m (kg-m, in-lb) ...Other materials:
P0102, P0103 MAF SENSOR
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn
ignition switch OFF and wait at
least 10 seconds before conducting the next test.
Which DTC is detected?
P0102 >> GO TO 2.
P0103 & ...
Draining
1. Start engine and let it run to warm up transaxle.
2. Stop engine. Remove drain plug (1) and gasket, using a socket
[Commercial service tool] and then drain gear oil.
3. Set a gasket on drain plug and install it to clutch housing, using
a socket [Commercial service tool].
CAUTION:
Never re ...
Throttle valve closed position learning
Description
Throttle Valve Closed Position Learning is an operation to learn the fully
closed position of the throttle valve by
monitoring the throttle position sensor output signal. It must be performed each
time harness connector of
electric throttle control actuator or ECM is disconnected. ...