Nissan Juke Service and Repair Manual : B1087 seat belt Pre-tensioner LH

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected? YES >> Refer to SRC-75, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace wiring harness.

3.REPLACE SEAT BELT PRE-TENSIONER

1. Replace seat belt pre-tensioner LH. Refer to SR-32, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-75, "DTC Logic".

Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-75, "DTC Logic".

Is DTC detected?

YES >> GO TO 1.

NO >> INSPECTION END

    B1086 seat belt Pre-tensioner LH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    B1088 seat belt Pre-tensioner LH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    Other materials:

    Exploded View
    M/T models 1. Clamp 2. Water hose 3. Oil cooler 4. Water hose N·m (kg-m, in-lb) CVT models 1. Clamp 2. Water hose 3. Oil cooler 4. Water hose 5. Water hose 6. Heater thermostat 7. Water hose A. To CVT oil warmer : N·m (kg-m, in-lb) ...

    Blower motor
    Diagnosis Procedure 1.CHECK SYMPTOM Check symptom (A, B or C). Which symptom is detected? A >>GO TO 2. B >>GO TO 11. C >> GO TO 13. 2.CHECK FUSE 1. Turn ignition switch OFF. 2. Check following fuses. - 10A fuse [No. 15, located in fuse block (J/B)] - 15A fuses [Nos ...

    C1121, C1123, C1125, C1127 ABS out valve system
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.CHECK DTC DETECTION With CONSULT ...