Nissan Juke Service and Repair Manual : B1024 pass A/B deact SW

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected? YES >> Refer to SRC-34, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 minutes.

(To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the connection normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Are the harness external parts normal (no damage)? YES >> GO TO 3.

NO >> Replace wiring harness.

3.CHECK AIR BAG CUTOFF SWITCH

1. Replace air bag cutoff switch..

2. Perform DTC confirmation procedure. Refer to SRC-34, "DTC Logic".

Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-34, "DTC Logic".

Is DTC detected?

YES >> GO TO 1.

NO >> INSPECTION END

    B1023 passenger air bag off indicator
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    B1026, B1027, B1028, B1029, B1030, B1031 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    Other materials:

    Evaporative emission system
    Inspection 1. Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections, chafing and deterioration. 2. Check EVAP canister as follows: a. Block port (A). Orally blow air through port (B). Check that air flows freely through port (C). b. Block port (B ...

    Air cleaner and air duct
    Exploded View 1. Hose clamp 2. PCV hose 3. Hose clamp 4. Air cleaner filter 5. Air cleaner filter case 6. Grommet 7. Inlet air duct (lower) 8. Grommet 9. Inlet air duct (upper) 10. Bracket 11. Air cleaner case 12. O-ring 13. Mass air flow sensor 14. Air duct A. To electric ...

    Unit removal and installation
    Engine assembly 2WD 2WD : Exploded View 1. Washer 2. Upper torque rod (RH) 3. Engine mounting insulator (RH) 4. Rear torque rod bracket 5. Rear torque rod 6. Engine mounting insulator (LH) 7. Engine mounting frame support (LH) 8. Engine mounting bracket (LH) : N·m (kg-m, ft-lb) : ...